BMW · Mini · Rolls-Royce7980 codes

BMW · Mini · Rolls-Royce — fault codes starting with 79

80 fault codes starting with 79 on BMW · Mini · Rolls-Royce vehicles, with descriptions: 790000, 790001, 790002 and more. Look up a code, read what it means.

Fault codes
80
Block
79
Make group
BMW · Mini · Rolls-Royce
Source language
English · German

The 80 BMW · Mini · Rolls-Royce fault codes that start with 79, with descriptions.

CodeDescriptionGerman
790000Error writing EepromFehler beim Eeprom Schreiben
790001Error reading EepromFehler beim Eeprom Lesen
790002Error in the Eeprom control areaFehler im Eeprom Control Bereich
790003Error when deleting EepromFehler beim Eeprom Löschen
790004Write error in Eeprom completelyFehler beim Eeprom komplett schreiben
790005Read error in Eeprom completelyFehler beim Eeprom komplett lesen
790006Error in the configuration ID of the EepromFehler in der Konfigurations-ID des Eeprom
790007Message (seconds counter time message): failureBotschaft (Sekundenzähler Zeitbotschaft): Ausfall
790008Diagnosis master queue deletedDiagnose Master Queue gelöscht
790009Diagnosis master queue fullDiagnose Master Queue voll
79000AReset due to Exceeding the task runtimeReset wg. Überschreitung der Tasklaufzeit
79000BVoltage regulator shutdown failedSpannungsreglerabschaltung fehlgeschlagen
79000Cthe external watchdog has triggered a resetder externe Watchdog hat einen Reset ausgelöst
79000Dthere was a reset due to of the SWI interrupt executedes wurde ein Reset wg. des SWI-Interrupts ausgeführt
79000Ethere was a reset due to of the XIRQ interrupt executedes wurde ein Reset wg. des XIRQ-Interrupts ausgeführt
79000Fthere was a reset due to an invalid OP code was executedes wurde ein Reset wg. eines ungültigen OP-Codes ausgeführt
790010there was a reset due to of a COP failure interrupt executedes wurde ein Reset wg. eines COP-Failure-Interrupts ausgeführt
790011there was a reset due to of the clock monitor interrupt executedes wurde ein Reset wg. des Clock monitor Interrupts ausgeführt
790012there was a reset due to of the CRG PLL lock interrupt executedes wurde ein Reset wg. des CRG PLL lock-Interrupts ausgeführt
790013there was a reset due to of the CRG self-clock mode interrupt executedes wurde ein Reset wg. des CRG self-clock mode-Interrupts ausgeführt
790014there was a reset due to an unexpected interrupt executedes wurde ein Reset wg. eines nicht erwarteten Interrupts ausgeführt
790015the operating system has a reset wg. triggered by a recognized errordas Betriebssystem hat einen Reset wg. eines erkannten Fehlers ausgelöst
790020NM-Timeout Timer has abnormally expired outside of the Ready Sleep StateNM-Timeout Timer has abnormally expired outside of the Ready Sleep State
790021Error in the Eeprom control areaFehler im Eeprom Control Bereich
790022NVM_E_INTEGRITY_FAILEDNVM_E_INTEGRITY_FAILED
790023Transmit buffers fullTransmit buffers full
790024CAN interface is in STOPPED modeCAN Interface is in STOPPED mode
790025NM initialization has failedNM initialization has failed
790026Call of CanIf function CanIf_Transmit has failedCall of CanIf function CanIf_Transmit has failed
790027Another error occurred during a reception or a transmissionAnother error occurred during a reception or a transmission
790028NM transmission path has failedNM transmission path has failed
790029Errors were detected during the respective action in the FLSbei der jeweiligen Aktion in der FLS wurden Fehler erkannt
79002AFlash write failed (HW)Flash write failed (HW)
79002BFlash read failed (HW)Flash read failed (HW)
79002CErrors were detected during the respective action in the FLSbei der jeweiligen Aktion in der FLS wurden Fehler erkannt
79002DMCU_E_CLOCK_FAILUREMCU_E_CLOCK_FAILURE
79002EMCU_E_LOCK_FAILUREMCU_E_LOCK_FAILURE
79002FDisabling of watchdog not allowedDisabling of watchdog not allowed
790030Switching between watchdog modes failed.Switching between watchdog modes failed.
790031Watchdog drivers mode switch has failedWatchdog drivers mode switch has failed
790032Timeout caused by hardware errorTimeout caused by hardware error
790033FEE_E_WRITE_FAILEDFEE_E_WRITE_FAILED
790034Vehicle status message (0x3A0): failureBotschaft Fahrzeugzustand (0x3A0): Ausfall
790035Start transmission has failedStart transmission has failed
790036Stop transmission has failedStop transmission has failed
790037The service EcuM_KillAllRUNRequests was issuedThe service EcuM_KillAllRUNRequests was issued
790038COMM_E_NET_START_IND_CHANNEL_0COMM_E_NET_START_IND_CHANNEL_0
79003AAlive supervision has failed and a watchdog reset will occurAlive-supervision has failed and a watchdog reset will occur
79003BAccess to FlexRay CC event idAccess to FlexRay CC event id
79003CJob List Execution lost synchronicity to the FlexRay Global TimeJob List Execution lost synchronicity to the FlexRay Global Time
79003DNo / incorrect communication to transceiver.No/incorrect communication to transceiver.
79003Esending of a service message failedsending of a service message failed
79003FMCU_E_QUARTZ_FAILUREMCU_E_QUARTZ_FAILURE
790040MCU_E_LCLOCK_0_FAILUREMCU_E_LCLOCK_0_FAILURE
790041MCU_E_HCLOCK_0_FAILUREMCU_E_HCLOCK_0_FAILURE
790042MCU_E_LOCK_0_FAILUREMCU_E_LOCK_0_FAILURE
790043MCU_E_RCCLOCK_0_FAILUREMCU_E_RCCLOCK_0_FAILURE
790044MCU_E_LCLOCK_1_FAILUREMCU_E_LCLOCK_1_FAILURE
790045MCU_E_HCLOCK_1_FAILUREMCU_E_HCLOCK_1_FAILURE
790046MCU_E_RCCLOCK_1_FAILUREMCU_E_RCCLOCK_1_FAILURE
790047MCU_E_LOCK_1_FAILUREMCU_E_LOCK_1_FAILURE
790048MCU_E_TIMEOUT_TRANSITIONMCU_E_TIMEOUT_TRANSITION
790049MCU_E_TIMEOUT_OSC_STABILITYMCU_E_TIMEOUT_OSC_STABILITY
79004AWDG_E_MISS_TRIGGERWDG_E_MISS_TRIGGER
79004BMCU_E_RC_MEASUREMCU_E_RC_MEASURE
79004CFLS_E_UNEXPECTED_FLASH_IDFLS_E_UNEXPECTED_FLASH_ID
79004DCANNM_E_NETWORK_TIMEOUTCANNM_E_NETWORK_TIMEOUT
79004FFEE_E_CACHE_READFEE_E_CACHE_READ
790050FEE_E_GC_ERASEFEE_E_GC_ERASE
790051FEE_E_GC_READFEE_E_GC_READ
790052FEE_E_GC_WRITEFEE_E_GC_WRITE
790053FEE_E_INITFEE_E_INIT
790054FEE_E_INVALIDATEFEE_E_INVALIDATE
790055FEE_E_READFEE_E_READ
790056FEE_E_WRITE_CYCLES_EXHAUSTEDFEE_E_WRITE_CYCLES_EXHAUSTED
790057FLS_E_OPERFLS_E_OPER
790058FLS_E_PROTECTION_FAILEDFLS_E_PROTECTION_FAILED
790059FEE_E_WRITEFEE_E_WRITE
790065Control unit: system resetSteuergerät: System Reset
790066Control unit: HW system resetSteuergerät: HW System Reset

Other blocks

Makes that use these codes

Code descriptions are shown in their source language; records without a translation stay raw. Source: CarCoding fault code database.

Get CarCoding

Connect your ELM327 adapter, read fault codes, and browse module settings on supported vehicles.

App Store Google Play

The app is free to download.