Audi · Porsche · Bentley · Lamborghini — C0 ile başlayan arıza kodları

Arıza kodu

797

Blok

C0

Marka grubu

Audi · Porsche · Bentley · Lamborghini

Kaynak dili

İngilizce

Audi · Porsche · Bentley · Lamborghini arıza kodlarından C0 ile başlayan 797 tanesi, açıklamalarıyla birlikte.

C00

Kod	Açıklama
C0000	Electronic control unit (ECU) defective (ROM: checksum test faulty).
C0001	Electronic control unit (ECU) defective (microcontroller error signaling module: microcontroller hardware defective).
C0002	Electronic control module (ECU) faulty (central processing unit: data interruption or memory read error or commands are not correct)
C0003	Electronic control unit (ECU) defective (microcontroller error signaling module: signal fault).
C0004	Electronic control unit (ECU) defective (Bus and ECC RAM test: microcontroller RAM (ECC logic) or RAM bus or address decoder fault
C0005	Electronic control unit (ECU) defective (operating system: memory area too small).
C0006	Electronic control module (ECU) faulty (operating system: signal sent to microprocessor invalid)
C0007	Electronic control unit (ECU) defective (operating system: command processing outside cycle time).
C0008	Electronic control module (ECU) faulty (operating system: command not available)
C0009	Electronic control module (ECU) faulty (microcontroller-error signaling module: during system startup phase during safety)
C000A	Electronic control unit (ECU) defective (RAM: memory hardware initialisation function faulty).
C000B	Electronic control unit (ECU) defective (microcontroller RAM or RAM test faulty).
C000C	Electronic control module (ECU) faulty (microcontroller-error signaling module: during system startup phase during safety)
C000D	Electronic control unit (ECU) defective (CPU compare module: central processing unit comparison fault).
C000E	Electronic control unit (ECU) defective (High end timer: hardware faulty).
C000F	Electronic control unit (ECU) defective (High end timer: transmission (RAM addressing) faulty).
C0010	Electronic control unit (ECU) defective (High end timer: transmission faulty).
C0011	Electronic control unit (ECU) defective (High end timer: transmission (status) faulty).
C0012	Electronic control module (ECU) faulty (high end timer: transmission not yet completed)
C0013	Towing recognition control module No communication
C0014	CLAMP_ACTIVATION_FAILURE_ISO_FRONT_RIGHT
C0018	CLAMP_ACTIVATION_FAILURE_ISO_REAR_LEFT
C001C	CLAMP_ACTIVATION_FAILURE_ISO_REAR_RIGHT
C0020	Combine_Event_-The_test_of_the_charge-pump_on_1st_or_2nd_system_asic_has_detected_a_failure_(e.g._missing_capacitor)-RBCha_rgePu_m
C0021	Brake_boosting_capability_is_lost_in_IPB_system-RBSts_IPBHy_d_Plung_erLos_tPres_sureB_oost
C0022	PWR_SW_SLIP_CONTROL_SHORT
C0024	Electronic control unit (ECU) defective (operating system: system overload due to too many commands).
C0026	Left_APB_MotorSpeedSensor_supply_or_sensor_line_short-circuit_to_Ubat.-RBAPB_MSSLe_ftLin_eHigh
C0027	Right_APB_MotorSpeedSensor_supply_line_open._No_sensor_connected_or_sensor_has_an_issue-RBAPB_MSSRi_ghtLi_neOpe_n
C0028	Rear axle steering position sensor signal comparison, deviation too large
C0029	Motor for rear axle steering, actuator stuck open
C002B	Electronic control unit (ECU) defective (voltage comparison test of the ASICs faulty).
C002C	Electronic control unit (ECU) defective (Serial processing interface initialisation test of the ASICs faulty).
C002D	Electronic control unit (ECU) defective (serial processing interface message transmission to the ASICs faulty).
C002E	Electronic control module (ECU) faulty (serial processing interface message transmission to ASICs not yet completed)
C0030	Electronic control unit (ECU) defective (Persistent data management: EEPROM hardware defective (access fault)).
C0031	WSS_test_failure_of_WSS_FL_(Short_circuit_supply_line_to_UBATT_short_circuits_between_sensors_any_line_failure)-RBWss_TestF_LFail_
C0032	Left Front Wheel Speed Sensor Supply Circuit Short To Ground
C0033	Right Front Tone Wheel Mechanical Failure
C0034	WSS_test_failure_of_WSS_FR_(Short_circuit_supply_line_to_UBATT_short_circuits_between_sensors_any_line_failure)-RBWss_TestF_RFail_
C0035	Electronic control unit (ECU) defective (System IC: watchdog command processing outside the defined time window).
C0036	Electronic control unit (ECU) defective (System IC: watchdog counter faulty).
C0037	WSS_test_failure_of_WSS_RL_(Short_circuit_supply_line_to_UBATT_short_circuits_between_sensors_any_line_failure)-RBWss_TestR_LFail_
C0038	Left Rear Wheel Speed Sensor Supply Circuit Short To Ground
C0039	Right Rear Tone Wheel Mechanical Failure
C003A	WSS_test_failure_of_WSS_RR_(Short_circuit_supply_line_to_UBATT_short_circuits_between_sensors_any_line_failure)-RBWss_TestR_RFail_
C003B	Right Rear Wheel Speed Sensor Supply Circuit Short To Ground
C003C	Electronic control module (ECU) faulty (electrical enable signal is not switched on or off)
C003D	Electronic control module (ECU) faulty (hydraulic or electrical (if available) enable signal unexpectedly switched off)
C003E	Electronic control unit (ECU) defective (microcontroller RAM faulty).
C003F	Monitoring_of_wheel_direction_differences._Faulty_wheel_not_assignable-Wss_MonWh_eelDi_rGen
C0040	Electronic control unit (ECU) defective (semiconductor voltage: permitted band gap outside the valid range).
C0041	Electronic control unit (ECU) defective (Analog/Digital converter: self-test fault at the ADC pin).
C0042	Electronic control unit (ECU) defective (ASIC: internal voltage monitoring has detected a supply voltage fault).
C0043	Return fuel pump: return fuel pump overheated due to prolonged pump motor and valve control (high pressure)
C0044	Pressure_Sensor_1_Line_shorted_to_Supply_or_Interruption_of_Sensor_ground_or_Sensor_supply_or_Signal_line-RBPre_ssSen_t1Lin_eHigh
C0045	Pressure_Sensor_2_Line_shorted_to_Supply_or_Interruption_of_Sensor_ground_or_Sensor_supply_or_Signal_line.-RBPre_ssSen_t2Lin_eHigh
C0046	Electronic control module (ECU) faulty (persistent data management: EEPROM content not compatible (customer ID) or reprogramming)
C0047	Electronic control unit (ECU) defective (Persistent data management: EEPROM memory overflow) or reprogramming with incompatible
C0048	Brake Booster Travel Sensor Alignment or Adjustment Incorrect
C0049	Reduced_pressure_build_up_in_plunger._Sucked_air_inside_the_plunger_during_TTI_or_RPL_or_active_test_during_start_up.-AIM_RADAi_rP
C004A	Electronic control module (ECU) faulty (ASIC or microcontroller: hardware components not supported by software)
C004B	Brake_fluid_sensor_line_is_short_to_power_supply-RBBra_keFlu_idLev_elOut_OfRan_geHig_h
C004C	Electronic control module (ECU) faulty (ASIC: software configuration does not match hardware configuration of voltage regulator)
C0050	Leakage_of_hydraulic_backup_circuit_components._And_/_or_Air_contamination_of_hydraulic_backup_circuit_components.-LEM_Leaka_geAnd
C0051	Steering Wheel Position Sensor Component Internal Failure
C0061	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail10 and
C0062	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail9 and
C0063	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail8 and
C0064	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail6 and
C0065	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail11 and
C0066	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail7 and
C006A	Multi-axis Acceleration Sensor Commanded Position Not Reachable
C006B	Continuous_ABS_control_for_implausible_long_time-Abs_ContC_ontro_l
C006C	Continuous_VDC_control_for_implausible_long_time
C006F	Hydraulic_module_is_in_assembly_mode-PSM_Devic_eNotF_illed_OrNot_Insta_lled
C0070	RF ABS Solenoid #1 Circuit Malfunction
C0071	Brake light switch: pressure sensor signal to brake light switch status not plausible (threshold 1. pBefore above 10 bar)
C0072	Brake Temperature Too High Over Temperature
C0074	Requested Driving Torque - General Signal Failure (OrngPlausTqMon_OoRSpdctrl)
C0075	Pedal_Travel_Sensor_(PTS)_Magnet_missing._The_monitoring_detects_an_invalid_duty_cycle
C0076	Brake light switch: brake light switch (signal) is permanently switched (Sm)
C0077	Brake light switch: the brake light switch supply voltage (BLS_12V) has undervoltage.
C0078	Tire Diameter Invalid / Incompatible Configuration
C0079	SECOBD:_Variable_Effort_Steering_ECU_Defective
C007A	Power supply (electronic control module (ECU)-wake up voltage): power supply line ignition/terminal 15 (12V) is
C0080	LR ABS Solenoid #1 Circuit Malfunction
C0081	Brake disc temperature model: an active brake intervention (pressure build-up) with simultaneous overheating of at least one brake disc
C0082	Brake System Malfunction Indicator
C0089	TCS Disable Switch Actuator Stuck Closed
C0090	4WD/AWD Power Transfer Unit Actuator Circuit Current Above Threshold
C00A1	Driveline Control Module Invalid / Incompatible Software Component
C00A6	4WD/AWD Transfer Case Unit Actuator Commanded Position Not Reachable
C00AA	RFE_coding_bit_is_set_to_0x04(TCS_VDC_EDC_is_OFF_ABS_reduced_EBV_on)_by_variant-RBVAR_TcsVd_cEdcA_BSRed_uced_OffBy_Varia_nt
C00B0	Wheel speed sensor: several wheel speed sensor faults have occurred or interference in the ABS control.
C00B5	Fahrzeugdynamikregelung: Fahrzeugdynamikregelung kontinuierlich.

C01

Kod	Açıklama
C0100	Supply voltage (electronic control unit (ECU) - hydraulics): the supply voltage (UB_ECU or UB_VR) has undervoltage.
C0102	Variant code: configuration (hydraulic unit (HU) coding) not correct or hydraulic unit type does not match vehicle
C0105	Power supply (electronic control module (ECU)-valve relay): power supply (UB_VR) has very high under
C0106	Supply voltage (electronic control unit (ECU) - hydraulics): the supply voltage (UB_ECU or UB_VR) has an increased undervoltage.
C0107	Power supply (electronic control module (ECU)-valve relay/valves): power supply (UB_VR) is not sufficient
C0110	Supply voltage (electronic control unit (ECU) - network): the supply voltage (UB_ECU) has undervoltage.
C0111	Supply voltage (electronic control unit (ECU) - network): the supply voltage (UB_ECU) has overvoltage.
C0112	4112: Control module faulty
C0113	Electronic control unit (ECU) defective (data area: CAN controller (RAM) faulty).
C0115	Electronic control unit (ECU) defective (control area: communication timeout fault (access to CAN controller faulty)).
C0116	t.b.d. 6
C0120	Supply voltage (electronic control unit (ECU)): the supply voltage (UB_ECU or UB_VR) has overvoltage.
C0121	Electronic control module (ECU) faulty (control module voltage monitoring error)
C0126	Electronic control module (ECU) faulty (simultaneous and contradictory access to outlet valves)
C0140	Electronic control module (ECU) faulty (watchdog status during failsafe circuit test (FSA) not correct)
C0141	Left TCS Solenoid #1 Circuit Malfunction
C0146	Left TCS Solenoid #2 Circuit Malfunction
C0150	Drucksensorkreis Hauptbremszylinder MC1: Kein Drucksensorsignal.
C0151	Right TCS Solenoid #1 CKT Malfunction
C0152	Drucksensorkreis Hauptbremszylinder MC1: Drucksensor beim Testpulsvergleich aufgrund Verstaerkungsfehler ausgefallen.
C0156	Right TCS Solenoid #2 CKT Malfunction
C0162	Electronic control module (ECU) faulty (motor relay status during failsafe circuit test (FSA) not correct)
C0163	Electronic control module (ECU) faulty (reset status hydraulic flip-flop during failsafe circuit test (FSA) not correct)
C0170	Hill hold control or automatic vehicle holding: reverse gear is permanently not activated
C0171	Hill hold control oder Automatisches Fahrzeughalten: Der Rueckwaertsgang ist permanent aktiviert.
C0173	Electronic control module (ECU) faulty (system IC: clock timing error)
C0180	Wheel speed sensor: 3 wheel speed sensor faults occurred at the same time.
C0181	Wheel speed sensor: 3 to 4 wheel speed sensor faults occurred at the same time.
C0185	Power supply (electronic control module (ECU)-speed sensor): power supply of at least one speed sensor
C0191	Electronic control module (ECU) faulty (motor relay: internal return fuel pump connection between microcontroller and)
C0195	Return fuel pump: motor relay has short circuit (motor relay status monitoring (ASIC))
C0196	Rueckfoerderpumpe: Das Motorrelais ist ueberlastet (Motorrelais-Statusueberwachung (ASIC)).
C0197	Return fuel pump: generated pump motor voltage (UMR) is too high or pump motor lines are interrupted or motor
C0198	Return fuel pump: generated pump motor voltage (UMR) is not sufficiently available (pump motor test)
C019B	Electronic control unit (ECU) defective (Intelligent free wheeling switch: motor free wheeling switch is faulty).
C019C	Electronic control module (ECU) faulty (return fuel pump ASIC: motor relay pullup switch (resistor) control is not)
C019E	Return fuel pump: motor relay control is incorrectly possible (motor relay gate test and hydraulic shutdown test)
C019F	Return fuel pump: motor relay control is not possible (motor relay gate test)
C01A0	Rueckfoerderpumpe: Die Pumpenmotorspannung (UPM) ist zu hoch.
C01A1	Rueckfoerderpumpe: Die Pumpenmotorspannung (UPM) ist zu niedrig.
C01A2	Return fuel pump: power supply (UB_MR) is too low or power supply line is interrupted (motor relay)
C01C0	Electronic control unit (ECU) defective (Analog/Digital converter: self-test fault at the vacuum sensor (front chamber) pin or at
C01C1	Power supply (electronic control module (ECU)-vacuum sensor): power supply (UB_ECU) and equivalent internal
C01C2	Power supply (electronic control module (ECU)-vacuum sensor): internal power supply (U5V_EXT) has short circuit
C01C3	Power supply: signal line is interrupted or has short circuit to ground or to internal power supply (U5V)
C01C4	t.b.d. 5
C01C5	t.b.d. 4
C01C6	t.b.d. 3
C01C7	Vacuum sensor: vacuum not plausible (vacuum sensor signal outside valid range)
C01D0	Valve relay: valve voltage (UVR) or output value (Qx) from valve driver has short circuit to ground
C01D1	Valve relay: valve voltage (UVR) or output value (Qx) from valve driver has high-impedance short circuit to ground
C01D2	Valve relay: valve relay control is not possible (valve relay gate control)
C01D3	Valve relay: valve relay is not switched on (valve relay gate test)
C01D4	Electronic control module (ECU) faulty (fixed built-in safe test not correct)
C01D5	Valve relay: valve relay is not switched off (valve relay gate test)
C01D9	Electronic control module (ECU) faulty (built-in safe test: interruption of communication in microprocessor monitored by system)
C01DA	Electronic control module (ECU) faulty (built-in safe test detects different microprocessor errors detected by system)
C01E1	Electronic control module (ECU) faulty (CAN RAM checkpattern test in algorithm server (AS) faulty)
C01E3	Electronic control module (ECU) faulty (RAM checkpattern test in algorithm server (AS) faulty)
C01E4	Electronic control module (ECU) faulty (RAM addressing test in algorithm server (AS) faulty)
C01E5	Electronic control module (ECU) faulty (ROM checksum test in algorithm server (AS) faulty)
C01E6	Electronic control module (ECU) faulty (built-in safe test: general error in algorithm server (AS))
C01EB	Electronic control module (ECU) faulty (boot ROM checksum test in algorithm server (AS) faulty)
C01F0	Electronic control unit (ECU) defective (software version of the electronic control unit (ECU) corresponds to the software version of the

C02

Kod	Açıklama
C0200	Beschleunigungssensor (integriert): Beschleunigungssensor A2 erkennt einen Signalbereichsfehler.
C0201	Beschleunigungssensor (integriert): Beschleunigungssensor A1 erkennt einen Signalbereichsfehler.
C0210	Brake light switch: brake light switch (signal) is permanently switched (HHC)
C0220	Network: CAN bus lines (H and L) have short circuit to each other or CAN bus line (H) has short circuit to positive or
C0221	RF Wheel Speed Sensor Circuit Open
C0222	RF Wheel Speed Signal Missing
C0223	RF Wheel Speed Signal Erratic
C0224	Network: CAN bus line (H or L) is interrupted or CAN bus (CAN0) is disturbed
C0225	LF Wheel Speed Sensor Circuit Open
C0226	LF Wheel Speed Signal Missing
C0227	LF Wheel Speed Signal Erratic
C0229	Drop Out of Front Wheel Speed Signals
C0235	Rear Wheel Speed Signal Circuit Open
C0236	Rear Wheel Speed Signal Circuit Missing
C0237	Rear Wheel Speed Signal Erratic
C0238	Wheel Speed Mismatch
C0240	Auslassventil VL: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C0241	C0254 EBCM Control Valve Circuit
C0242	Auslassventil VL: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C0243	Auslassventil VL: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C0244	Auslassventil VL: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C0245	Outlet valve front left: voltage signal (Qx or gate) from the valve driver faulty.
C0246	Outlet valve front left: fault current (Qx to ground) inside or outside the valve driver.
C0250	Auslassventil VR: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C0251	Outlet valve FR: short circuit between two valves or valve spool faulty
C0252	Auslassventil VR: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C0253	Auslassventil VR: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C0254	Auslassventil VR: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C0255	Outlet valve front right: voltage signal (Qx or gate) from the valve driver faulty.
C0256	Outlet valve front right: fault current (Qx to ground) inside or outside the valve driver.
C0260	Auslassventil HL: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C0261	Outlet valve RL: short circuit between two valves or valve spool faulty
C0262	Auslassventil HL: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C0263	Auslassventil HL: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C0264	Auslassventil HL: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C0265	Outlet valve rear left: voltage signal (Qx or gate) from the valve driver faulty.
C0266	Outlet valve rear left: fault current (Qx to ground) inside or outside the valve driver.
C0269	or C0274 Excessive Dump/Isolation Time
C0270	Auslassventil HR: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C0271	C0273 EBCM Malfunction
C0272	Auslassventil HR: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C0273	Auslassventil HR: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C0274	Auslassventil HR: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C0275	Outlet valve rear right: voltage signal (Qx or gate) from the valve driver faulty.
C0276	Outlet valve rear right: fault current (Qx to ground) inside or outside the valve driver.
C0280	Einlassventil VL: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C0281	Inlet valve FL: short circuit between two valves or valve spool faulty
C0282	Einlassventil VL: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C0283	Einlassventil VL: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C0284	Einlassventil VL: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C0286	ABS Indicator Lamp Circuit Shorted to B+
C0287	Inlet valve front left: fault current (Qx to ground) inside or outside the valve driver.
C0288	Brake Warning Lamp Circuit Shorted to B+
C0290	Einlassventil VR: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C0291	Inlet valve FR: short circuit between two valves or valve spool faulty
C0292	Einlassventil VR: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C0293	Einlassventil VR: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C0294	Einlassventil VR: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C0296	Inlet valve front right: voltage signal (Qx or gate) from the valve driver faulty.
C0297	Inlet valve front right: fault current (Qx to ground) inside or outside the valve driver.
C0298	Einlassventil VR: Ventilfreilauffunktion vom Ventiltreiber fehlerhaft.
C02A0	Einlassventil HL: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C02A1	Inlet valve RL: short circuit between two valves or valve spool faulty
C02A2	Einlassventil HL: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C02A3	Einlassventil HL: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C02A4	Einlassventil HL: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C02A6	Inlet valve rear left: voltage signal (Qx or gate) from the valve driver faulty.
C02A7	Inlet valve rear left: fault current (Qx to ground) inside or outside the valve driver.
C02A8	Einlassventil HL: Ventilfreilauffunktion vom Ventiltreiber fehlerhaft.
C02B0	Einlassventil HR: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C02B1	Inlet valve RR: short circuit between two valves or valve spool faulty
C02B2	Einlassventil HR: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C02B3	Einlassventil HR: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C02B4	Einlassventil HR: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C02B6	Inlet valve rear right: voltage signal (Qx or gate) from the valve driver faulty.
C02B7	Inlet valve rear right: fault current (Qx to ground) inside or outside the valve driver.
C02B8	Einlassventil HR: Ventilfreilauffunktion vom Ventiltreiber fehlerhaft.
C02C0	Roller bench test: misuse of roller bench test function has occurred
C02C1	Roller Bench Test: Die Funktion Roller Bench Test ist aktiviert.
C02D0	High-pressure switching valve 1: short circuit between two valves or valve spool faulty
C02D1	Hochdruckschaltventil 1: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C02D2	Hochdruckschaltventil 1: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C02D3	Hochdruckschaltventil 1: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C02D4	High-pressure switching valve 1: voltage signal (Qx or gate) from the valve driver faulty.
C02D5	High-pressure switching valve 1: fault current (Qx to ground) inside or outside the valve driver.
C02D6	Hochdruckschaltventil 1: Ventilfreilauffunktion vom Ventiltreiber fehlerhaft.
C02E0	Hochdruckschaltventil 1: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C02E1	Hochdruckschaltventil 2: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C02E2	High-pressure switching valve 2: short circuit between two valves or valve spool faulty
C02E3	Hochdruckschaltventil 2: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C02E4	Hochdruckschaltventil 2: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C02E5	Hochdruckschaltventil 2: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C02E6	High-pressure switching valve 2: voltage signal (Qx or gate) from the valve driver faulty.
C02E7	High-pressure switching valve 2: fault current (Qx to ground) inside or outside the valve driver.
C02E8	Hochdruckschaltventil 2: Ventilfreilauffunktion vom Ventiltreiber fehlerhaft.
C02F0	Umschaltventil 1: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C02F1	Switching valve 1: short circuit between two valves or valve spool faulty
C02F2	Umschaltventil 1: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C02F3	Umschaltventil 1: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C02F4	Umschaltventil 1: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C02F5	Umschaltventil 1: Ventilansteuerung (Stromvergleich) vom Ventiltreiber fehlerhaft.
C02F6	Changeover valve 1: voltage signal (Qx or gate) from the valve driver faulty.
C02F7	Changeover valve 1: fault current (Qx to ground) inside or outside the valve driver.
C02F8	Umschaltventil 1: Ventilfreilauffunktion vom Ventiltreiber fehlerhaft.

C03

Kod	Açıklama
C0300	Umschaltventil 2: Aktivierungsregister vom Ventiltreiber fehlerhaft.
C0301	Switching valve 2: short circuit between two valves or valve spool faulty
C0302	Umschaltventil 2: Ventilwiderstand ausserhalb dem gueltigen Bereich.
C0303	Umschaltventil 2: Interne Hardwarerueckmeldung vom Ventiltreiber fehlerhaft.
C0304	Umschaltventil 2: Ausgangswert (Qx-On oder Qx-Off) vom Ventiltreiber fehlerhaft.
C0305	Umschaltventil 2: Ventilansteuerung (Stromvergleich) vom Ventiltreiber fehlerhaft.
C0306	Changeover valve 2: voltage signal (Qx or gate) from the valve driver faulty.
C0307	Changeover valve 2: fault current (Qx to ground) inside or outside the valve driver.
C0308	Motor A/B Circuit Low
C0309	Motor A/B Circuit High
C0310	Motor A/B Circuit Open
C0311	Electronic control unit (ECU) defective (high-end timer: transmission (wheel speed sensor signals) faulty).
C0312	Electronic control unit (ECU) defective (system IC: hardware wheel speed sensor test faulty).
C0313	Supply voltage (electronic control unit (ECU) - wheel speed sensors): the supply voltage of the wheel speed sensors has a
C0314	Wheel speed sensor: wheel speed sensor signal faulty at more than one wheel.
C0315	Motor Ground Circuit Open
C0321	Drehratensensor: Drehratensensor erkennt einen Signalbereichsfehler (Stillstand).
C0322	Drehratensensor: Drehratensensor erkennt einen Signalbereichsfehler.
C0323	T-Case Lock Circuit Low
C0324	T-Case Lock Circuit High
C0325	Drehratensensor: Drehratensensor erkennt einen Schnellabgleich-Offsetfehler (Offset2).
C0326	Drehratensensor: Drehratensensor erkennt einen Schnellabgleich-Offsetfehler (Offset1).
C0327	Drehratensensor (integriert): Drehratensensor erkennt einen Empfindlichkeits-Gierratenfehler.
C0328	Drehratensensor: Drehratensensor erkennt einen Langzeitabgleich-Offsetfehler.
C0329	Drehratensensor: Drehratensensor erkennt einen Signalgradientfehler.
C032A	Drehratensensor: Drehratensensor erkennt einen Installationsfehler.
C032B	Drehratensensor: Drehratensensor erkennt einen Empfindlichkeits-Abgleichsfehler.
C032C	Drehratensensor: Drehratensensor erkennt einen Vergleichsfehler.
C032D	Drehratensensor: Drehratensensor erkennt einen Modell-gestuetzten Vergleichsfehler.
C032E	Yaw rate sensor: yaw rate sensor detects faulty signal states in the model-based comparison with the steering angle sensor.
C0330	Laengsbeschleunigungssensor: Laengsbeschleunigungssensor erkennt einen Langzeitabgleich-Offsetfehler.
C0331	Laengsbeschleunigungssensor: Laengsbeschleunigungssensor erkennt einen Vergleichsfehler (1.5 m/s2).
C0332	Laengsbeschleunigungssensor: Laengsbeschleunigungssensor erkennt einen Vergleichsfehler (4 m/s2).
C0333	Laengsbeschleunigungssensor: Laengsbeschleunigungssensor erkennt einen Vergleichsfehler (3.5 m/s2).
C0334	Longitudinal acceleration sensor (integrated): electronic control module (ECU) not installed correctly (offset value in longitudinal acceleration)
C0340	Querbeschleunigungssensor: Querbeschleunigungssensor erkennt einen Langzeitabgleich-Offsetfehler.
C0341	Querbeschleunigungssensor: Querbeschleunigungssensor erkennt einen Stillstand-Offsetfehler.
C0342	Querbeschleunigungssensor: Querbeschleunigungssensor erkennt einen Modell-gestuetzten Vergleichsfehler.
C0343	Querbeschleunigungssensor: Querbeschleunigungssensor erkennt einen Vergleichsfehler.
C0344	Lateral acceleration sensor (integrated): electronic control module (ECU) not installed correctly (offset value in lateral acceleration)
C0357	Park Switch Circuit High
C0362	4LO Discrete Output Circuit High
C0365	Actuator and sensor monitoring (ACM): pressure sensor signal to brake light switch status not plausible (threshold 1. pBefore > 15 bar)
C0367	Front Axle Control Circuit High
C0376	Front/Rear Shaft Speed Mismatch

C04

Kod	Açıklama
C0410	Speed sensor: speed sensor signal (direction of rotation) not correct
C0417	Wheel speed sensor front left: wheel speed sensor signal faulty (air gap too large (pulse wheel or multipole ring)).
C0418	Wheel speed sensor front left: wheel speed sensor signal faulty (pulse wheel or multipole ring defective or signal interference).
C041C	Speed sensor FL: speed sensor signal faulty (missing tooth (tone ring) or N/S pole not detected (multipole wheel))
C0420	Speed sensor: speed sensor on front axle mixed up
C042C	Speed sensor FL: speed sensor faulty or speed sensor line or speed sensor type not correct
C0430	Speed sensor signal line FL (DS) is interrupted or has short circuit to battery positive or ground. Speed sensor power
C0431	Speed sensor FL: signal line (DS) is interrupted or has short circuit to ground
C0432	Speed sensor FL: signal line (DS) has short circuit to positive
C0438	Speed sensor FL: power supply line (DP) has short circuit to ground
C043C	Speed sensor FL: speed sensor signal not plausible
C044E	Wheel speed sensor front right: wheel speed sensor fault occurred for a long time.
C044F	Speed sensor FR: different speed calculation in electronic control module (ECU)
C0450	Steering angle sensor: steering angle sensor does not detect correct number of messages
C0452	Steering angle sensor: steering angle sensor zero position not found (class 1) or steering angle sensor not initialized or calibrated
C0453	Steering angle sensor: steering angle sensor detects a signal range fault.
C0454	Steering angle sensor: steering angle sensor detects a signal gradient fault.
C0455	Steering angle sensor: steering angle sensor detects a long-term adjustment offset fault.
C0456	Wheel speed sensor front right: wheel speed sensor signal faulty (pulse wheel or multipole ring).
C0457	Wheel speed sensor front right: wheel speed sensor signal faulty (air gap too large (pulse wheel or multipole ring)).
C0458	Steering angle sensor: steering angle sensor detects faulty signal states in the model-based comparison with the yaw rate sensor.
C0459	Steering angle sensor: steering angle sensor detects a signal monitoring fault.
C045A	Speed sensor FR: speed sensor faulty or speed sensor line not correct
C045C	Speed sensor FR: speed sensor signal faulty (missing tooth (tone ring) or N/S pole not detected (multipole wheel))
C0460	Speed sensor FL: speed sensor signal (direction of rotation) not correct
C0468	Wheel speed sensor front right: wheel speed sensor signal faulty (air gap too large (multipole ring)).
C046A	Wheel speed sensor front right: wheel speed sensor signal faulty (signal width exceeded (multipole ring)).
C046C	Speed sensor FR: speed sensor faulty or speed sensor line or speed sensor type not correct
C0470	Speed sensor signal line FR (DS) is interrupted or has short circuit to battery positive or ground. Speed sensor power
C0472	Steering Handwheel Speed Sensor Signal V Low
C0473	Steering Handwheel Speed Sensor Signal V High
C0480	Speed sensor RL: speed sensor signal (direction of rotation) not correct
C0490	Speed sensor RR: speed sensor signal (direction of rotation) not correct
C0495	EVO Tracking Error
C0498	Steering Assist Control Actuator Feed Circuit Low
C0499	Steering Assist Control Solenoid Feed Circuit High
C049C	Speed sensor RL: speed sensor signal faulty (missing tooth (tone ring) or N/S pole not detected (multipole wheel))
C04A0	Speed sensor FL: signal line or power supply line is interrupted or has short circuit to ground or to
C04A5	Speed sensor FL: signal line is interrupted or has short circuit to ground or to positive. Power supply line
C04A6	Wheel speed sensor front left: wheel speed sensor signal faulty (air gap too large (multipole ring)).
C04A7	Speed sensor FL: speed sensor faulty or speed sensor line or speed sensor type not correct
C04A8	Wheel speed sensor rear left: wheel speed sensor signal faulty (air gap too large (multipole ring)).
C04AA	Wheel speed sensor rear left: wheel speed sensor signal faulty (signal width exceeded (multipole ring)).
C04AB	Speed sensor FL: speed sensor signal faulty (high-frequency signal interference) or multi-IC faulty or speed sensor type
C04AC	Wheel speed sensor front left: wheel speed sensor signal outside the valid range.
C04AD	Wheel speed sensor front left: wheel speed sensor signal faulty (air gap too large (multipole ring). Low).
C04AE	Wheel speed sensor front left: wheel speed sensor signal faulty (air gap too large (multipole ring). High).
C04AF	Speed sensor FL: speed sensor faulty or speed sensor line not correct
C04B0	Speed sensor signal line RL (DS) is interrupted or has short circuit to battery positive or ground. Speed sensor power
C04B1	Speed sensor RL: signal line (DS) is interrupted or has short circuit to ground
C04B2	Speed sensor FL: speed sensor signal faulty (missing tooth (tone ring) or N/S pole not detected (multipole wheel))
C04B3	Wheel speed sensor front left: wheel speed sensor signal faulty (multipole ring defective or signal interference).
C04B4	Wheel speed sensor front left: wheel speed sensor fault occurred for a certain time.
C04B5	Speed sensor FL: signal line has line interruption or short circuit to ground. Power supply line has
C04B6	Speed sensor FL: signal line has short circuit to positive
C04B7	Speed sensor FL: line condition not plausible (signal line or power supply line) or multi-IC faulty
C04B8	Speed sensor RL: power supply line (DP) has short circuit to ground
C04BC	Speed sensor RL: speed sensor signal not plausible
C04C0	Speed sensor FR: signal line or power supply line is interrupted or has short circuit to ground or to
C04C5	Speed sensor FR: signal line is interrupted or has short circuit to ground or to positive. Power supply line
C04C6	Wheel speed sensor front right: wheel speed sensor signal faulty (air gap too large (multipole ring)).
C04C7	Speed sensor FR: speed sensor faulty or speed sensor line or speed sensor type not correct
C04C8	Speed sensor FR: speed sensor type not correct
C04CB	Speed sensor FR: speed sensor signal faulty (high-frequency signal interference) or multi-IC faulty or speed sensor type
C04CC	Wheel speed sensor front right: wheel speed sensor signal outside the valid range.
C04CD	Wheel speed sensor front right: wheel speed sensor signal faulty (air gap too large (multipole ring). Low).
C04CE	Wheel speed sensor front right: wheel speed sensor signal faulty (air gap too large (multipole ring). High).
C04CF	Speed sensor RR: different speed calculation in electronic control module (ECU)
C04D0	Speed sensor FR: speed sensor signal faulty (N/S pole not detected (multipole wheel))
C04D2	Speed sensor FR: speed sensor signal faulty (missing tooth (tone ring) or N/S pole not detected (multipole wheel))
C04D3	Wheel speed sensor front right: wheel speed sensor signal faulty (multipole ring defective or signal interference).
C04D4	Wheel speed sensor front right: wheel speed sensor fault occurred for a certain time.
C04D5	Speed sensor FR: signal line has line interruption or short circuit to ground. Power supply line has
C04D6	Wheel speed sensor rear right: wheel speed sensor signal faulty (pulse wheel or multipole ring).
C04D7	Wheel speed sensor rear right: wheel speed sensor signal faulty (air gap too large (pulse wheel or multipole ring)).
C04D8	Wheel speed sensor rear right: wheel speed sensor signal faulty (pulse wheel or multipole ring defective or signal interference).
C04DA	Speed sensor RR: speed sensor faulty or speed sensor line not correct
C04DC	Speed sensor RR: speed sensor signal faulty (missing tooth (tone ring) or N/S pole not detected (multipole wheel))
C04E0	Speed sensor RL: signal line or power supply line is interrupted or has short circuit to ground or to
C04E5	Speed sensor RL: signal line is interrupted or has short circuit to ground or to positive. Power supply line
C04E6	Wheel speed sensor rear left: wheel speed sensor signal faulty (air gap too large (multipole ring)).
C04E7	Speed sensor RL: speed sensor faulty or speed sensor line or speed sensor type not correct
C04E8	Wheel speed sensor rear right: wheel speed sensor signal faulty (air gap too large (multipole ring)).
C04EA	Wheel speed sensor rear right: wheel speed sensor signal faulty (signal width exceeded (multipole ring)).
C04EB	Speed sensor RL: speed sensor signal faulty (high-frequency signal interference) or multi-IC faulty or speed sensor type
C04EC	Wheel speed sensor rear left: wheel speed sensor signal outside the valid range.
C04ED	Wheel speed sensor rear left: wheel speed sensor signal faulty (air gap too large (multipole ring). Low).
C04EE	Wheel speed sensor rear left: wheel speed sensor signal faulty (air gap too large (multipole ring). High).
C04EF	Speed sensor RL: speed sensor faulty or speed sensor line not correct
C04F0	Speed sensor signal line RR (DS) is interrupted or has short circuit to battery positive or ground. Speed sensor power
C04F1	Speed sensor RR: signal line (DS) is interrupted or has short circuit to ground
C04F2	Speed sensor RL: speed sensor signal faulty (missing tooth (tone ring) or N/S pole not detected (multipole wheel))
C04F3	Wheel speed sensor rear left: wheel speed sensor signal faulty (multipole ring defective or signal interference).
C04F4	Wheel speed sensor rear left: wheel speed sensor fault occurred for a certain time.
C04F5	Speed sensor RL: signal line has line interruption or short circuit to ground. Power supply line has
C04F6	Speed sensor RL: signal line has short circuit to positive
C04F7	Speed sensor RL: line condition not plausible (signal line or power supply line) or multi-IC faulty
C04F8	Speed sensor RR: power supply line (DP) has short circuit to ground
C04FC	Speed sensor RR: speed sensor signal not plausible

C05

Kod	Açıklama
C0500	WSS_test_failure_of_WSS_FL_(Short_circuit_supply_line_to_UBATT_short_circuits_between_sensors_any_line_failure)-RBWss_TestF_LFail_
C0501	Wrong_Parity_information_from_WSS_VDA_sensor_on_WSS_FL-RBWss_FLVda_Parit_yBitF_ail
C0502	WSS_FL_sensor_line_is_short_to_GND-RBWss_FLLin_eGnd
C0503	WSS_FL_sensor_line_is_short_Battery-RBWss_FLLin_eHigh
C0504	WSS_STANDSTILL_INVALID_PERIOD_FRONT_LEFT or WSS_VDA_TP_OUT_OF_RANGE_FRONT_LEFT
C0505	GbxStgyqm GbxStgyqm: C0031 left front wheel speed sensor
C0506	WSS_test_failure_of_WSS_FR_(Short_circuit_supply_line_to_UBATT_short_circuits_between_sensors_any_line_failure)-RBWss_TestF_RFail_
C0507	Wrong_Parity_information_from_WSS_VDA_sensor_on_WSS_FR-RBWss_FRVda_Parit_yBitF_ail
C0508	WSS_FR_supply_line_is_short_GND-RBWss_FRSup_plyGn_d
C0509	WSS_FR_sensor_line_is_short_Battery-RBWss_FRLin_eHigh
C050A	WSS_STANDSTILL_INVALID_PERIOD_FRONT_RIGHT or WSS_VDA_TP_OUT_OF_RANGE_FRONT_RIGHT
C050B	GbxStgyqm GbxStgyqm: C0033 right front wheel speed sensor
C050C	WSS_test_failure_of_WSS_RL_(Short_circuit_supply_line_to_UBATT_short_circuits_between_sensors_any_line_failure)-RBWss_TestR_LFail_
C050D	Wheel speed sensor rear right: wheel speed sensor signal faulty (air gap too large (multipole ring). Low).
C050E	Wheel speed sensor rear right: wheel speed sensor signal faulty (air gap too large (multipole ring). High).
C050F	Left Rear Wheel Speed Sensor Circuit High
C0510	WSS_STANDSTILL_INVALID_PERIOD_REAR_LEFT or WSS_VDA_TP_OUT_OF_RANGE_REAR_LEFT
C0511	Wss_fault_due_to_missing_wheel_speed-Wss_Signa_lLost_RL
C0512	WSS_test_failure_of_WSS_RR_(Short_circuit_supply_line_to_UBATT,_short_circuits_between_sensors,_any_line_failure)
C0513	Wheel speed sensor rear right: wheel speed sensor signal faulty (multipole ring defective or signal interference).
C0514	Wheel speed sensor rear right: wheel speed sensor fault occurred for a certain time.
C0515	WSS_RR_sensor_line_is_short_Battery-RBWss_RRLin_eHigh
C0516	WSS_STANDSTILL_INVALID_PERIOD_REAR_RIGHT or WSS_VDA_TP_OUT_OF_RANGE_REAR_RIGHT
C0517	GbxStgyqm GbxStgyqm: C003A right rear wheel speed sensor
C0518	Incorrect_Gap_between_sensor_element_and_the_cog_wheel_on_FL_wheel-RBWss_FLAir_Gap
C0519	Incorrect_Gap_between_sensor_element_and_the_cog_wheel_on_FR_wheel-RBWss_FRAir_Gap
C051A	Incorrect_Gap_between_sensor_element_and_the_cog_wheel_on_RL_wheel-RBWss_RLAir_Gap
C051B	Incorrect_Gap_between_sensor_element_and_the_cog_wheel_on_RR_wheel-RBWss_RRAir_Gap
C051C	Gain_monitoring_of_the_lat._acceleration_during_the_dynamic_verification_of_sensor_at_plant_EndOfLine_has_detected_an_error
C051D	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail5 and
C051E	Signal_SARA_CF_Accel_Y_b_red2_TempError_(3)
C051F	Combine_Event_-AXS_or_AYS_failure_due_to_longitudinal_or_lateral_acceleration_out_of_range(High)-AXS_MonVD_Range_High_OR_AYS_MonVD
C0520	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail1 and
C0522	SCL:_SARA_Omega_Z_b_red_-_Sensor_not_calibrated_error
C0523	SCL:_SARA_Omega_Z_b_red_-_Temporary_signal_error
C0525	"Primary Master" diagnosis for slave AirbagFunctions, based on failure info received from slave via signals IMU_StObd_StFail2 and
C0526	LWI_03_-_SAS_calibration_is_running_Signal_(LWI_StsCal_==_Not_Calibrated_(1))_ AND AND _(LWI_QlfrAgStgWhl_==_Outside_the_specifica
C0527	"Primary Master" diagnosis for slave LenkWinkelInformation, based on failure info received from slave via signals LWI_StOBD_StFail
C0528	SAS_failure_when_center_is_not_yet_found_and_vehicle_speed_or_time_exceeded._Failure_is_set_with_lamp_activation.-Sas_CondA_ctive_
C0529	"Primary Master" diagnosis for slave LenkWinkelInformation, based on failure info received from slave via signals LWI_StOBD_StFail
C052A	"Primary Master" diagnosis for slave LenkWinkelInformation, based on failure info received from slave via signals LWI_StOBD_StFail
C052B	The_test_of_the_charge-pump_on_second_system_asic_has_detected_a_failure_(e.g._missing_capacitor)-RBCha_rgePu_mpFai_lure_2ndSy_ste
C052C	ABS_MOTOR_OPEN or LOSS_OF_MOTOR_GROUND_FAULT or PM_BRIDGE_MOTOR_DRIVER_OPEN
C052E	PM_DRIVER_POWER_ON_RESET
C052F	Charge_pump_tests_on_second_system_asic_could_not_be_executed_because_of_undervoltage.-RBCha_rgePu_mpUnd_ervol_tage_2ndSy_stemA_si
C0530	BD_OFFSET_CALIBRATION_FAULT
C0532	BD_OVERCURRENT_FAULT
C0535	AktSp_undervoltage_replacement_fault_for_OBD_relevant_AktSp_undervoltage_faults
C053B	LOSS_OF_SOLENOID_GROUND_FAULT or SOL_OPEN_DUMP_FRONT_LEFT or SOL_OPEN_DUMP_FRONT_RIGHT or SOL_OPEN_DUMP_REAR_LEFT or SOL_OPEN_DUMP
C053C	TCS/VDC_temporarily_not_available_due_to_multiple_WSS_suspicion_(e.g._noise_sensor_undervoltage_...)-Wss_MoreT_hanOn_eSusp_ected
C053D	Pressure_Sensor_1_Sensor_internal_failure-RBPre_ssSen_t1Sen_sorIn_terna_l
C053E	Pressure_Sensor_1_Line_shorted_to_Supply_or_Interruption_of_Sensor_ground-RBPre_ssSen_t1Lin_eHigh
C053F	Pressure_Sensor_1_Line_shorted_to_Ground_or_Interruption_of_Sensorsupply_or_Signal_line-RBPre_ssSen_t1Lin_eLow
C0540	Brake Pressure Sensor "A" Circuit/Open
C0541	The_pressure_difference_between_front_and_rear_axle_during_last_hydraulic_braking_in_system_wake-up_phase_is_too_high.
C0542	Pressure_Sensor_2_Line_shorted_to_Ground_or_Interruption_of_Sensorsupply_or_Signal_line-RBPre_ssSen_t2Lin_eLow
C0543	Pressure_Sensor_2_Line_shorted_to_Supply_or_Interruption_of_Sensor_ground-RBPre_ssSen_t2Lin_eHigh
C0545	Vin_check_failed_due_to_mismatch_between_the_received_vin_from_bus_and_the_reference_vin-RBVAR_VinCh_eckFa_iled
C0546	VIN Not Programmed or Incompatible
C054A	AcmVs_BoosterLowVac_SeveralIgnitionCycles
C054B	Vacuum Sensor "A" Circuit Low
C054C	Vacuum Sensor "A" Circuit High
C054F	Vacuum_Sensor_2:_Line_is_low
C0550	Vacuum_Sensor_2:_Line_is_high
C0552	Longitudinal Acceleration Sensor Range/Performance
C0555	A_wheel_speed_sensor_with_wrong_sensor_type_is_mounted_on_wheel_FL-RBWss_FLWro_ngSen_s
C0556	A_wheel_speed_sensor_with_wrong_sensor_type_is_mounted_on_wheel_FR-RBWss_FRWro_ngSen_s
C0557	A_wheel_speed_sensor_with_wrong_sensor_type_is_mounted_on_wheel_RL-RBWss_RLWro_ngSen_s
C0558	A_wheel_speed_sensor_with_wrong_sensor_type_is_mounted_on_wheel_RR-RBWss_RRWro_ngSen_s
C0559	"Primary Master" diagnosis for slave Hinterachslenkung (HAL), based on failure info received from slave via signals HAL_StObd_StFa
C055B	Charge_pump_tests_on_second_system_asic_could_not_be_executed_because_of_undervoltage.-RBCha_rgePu_mpUnd_ervol_tage_2ndSy_stemA_si
C055C	PWR_SW_SLIP_CONTROL_DRV_CORRELATION
C055D	Pressure_in_rear_axle_too_low_compared_to_target_pressure_due_to_Ra_Hydraulic
C055E	ESC: Vorderachse Plausibilitaetsfehler Pedalweg zu Bremsvordruck
C055F	pV-deviation_of_active_circuits_which_indicate_a_reduced_brake_performance_in_hydraulic_backup.-AIM_AirBa_ckupC_ircui_tPass_ive
C0562	Brake Pedal Position Sensor Supply Voltage System Voltage
C0563	An_excessive_number_of_ECU_resets_has_occurred_in_a_row_during_actuator_initialization_(before_IPC_completion)-RBPSM_Succe_ssive_E
C0564	ABS Control Module System Voltage Low
C0565	ABS Control Module System Voltage High
C056A	Brake Booster Pressure Sensor Power Supply Circuit
C056D	RBLiPS12VCaused5VSupplyUndervoltage
C0579	BLM_Temperature_Sensor_2_Line_shorted_to_Ground-RBBLM_Tempe_ratur_eB6Ch_annel_2Line_Low
C057A	BLM_Temperature_Sensor_2_Line_shorted_to_Supply-RBBLM_Tempe_ratur_eB6Ch_annel_2Line_High
C057B	BLM_Temperature_Sensor_2_Line_shorted_to_Supply-RBBLM_Tempe_ratur_eB6Ch_annel_2Line_High
C057C	TEMP_SENSOR_DIODE_FAULT_1_RED
C057E	Brake Booster Temperature Sensor A/B Correlation Component or System Over Temperature
C057F	Brake Booster Motor A Phase U-V-W Circuit Current Below Threshold
C0586	SAct_ISplyVal
C0587	The_failure_is_logged_whenver_the_absolute_deviation_between_the_unfiltered_RPS_speed_and_filtered_speed_exceeds_711.2_rad/s_provi
C0588	RPSVectorLengthAbsoluteRangeLow
C0589	RPSVectorLengthAbsoluteRangeHigh
C058A	Motor_load_not_plausible_to_pressure_sensor_signal-PSCMo_torlo_adToP_ressu_reNot_Plaus_ibleF_ast
C058B	MPS2_COMM_FAULT
C058E	SAct_AgMotSnsrElecAgLut
C058F	Deviation_between_actul_regenerative_torque_and_target_regenerative_torque_is_too_high_(underbraked_vehicle)
C0590	RBBLM_Current1OffsetHigh
C0591	RBBLM_Current1OffsetLow
C0592	SAct_IOffsOutOfRngHi
C0593	SAct_IOffsShoCutGnd
C0594	Combine_Event_-Motor_load_not_plausible_to_pressure_sensor_signal-PSCMo_torlo_adToP_ressu_reNot_Plaus_ibleF_ast_or_Slow
C0595	UB_Valve_to_UBRD_INT_plausi_voltage_divider_drift_failure_(large_deviation_between_UB_Valve_to_UBRD_INT_voltage)-RBUBR_DINTP_lausi
C0596	Offset_Current_1_out_of_range_high-RBBLM_Curre_nt1Of_fsetH_igh
C0597	The_WssDynamicConfigurationFailure_is_set_if_after_ignition_on_the_configuration_of_the_wheel_speed_sensor_type_is_not_possible.-R
C0598	PDU_Rx_RBUIPBDiagResp-_AliveCounter-RBNet_Comsc_l_Rx_RBUIP_BDiag_Resp_Alive_Count_er
C0599	Mismatch_between_RPS_calibration_data_version_in_NvM_and_SW_version.-RPS_Wrong_Calib_DataV_ersio_n
C059A	Signal_HAL_Radwinkel_not_calibrated_(1021)
C05A4	wss_undervoltage_has_been_detected_for_FL_wheel-RBWss_FLUnd_erVol_tage
C05AD	Brake Blending System Performance
C05AF	Offset_Current_2_out_of_range_high-RBBLM_Curre_nt2Of_fsetH_igh
C05B3	SAct_TShoCutGnd
C05B4	SAct_TShoCutVcc
C05B6	Pressure_Sensor_1_Temperature_TimeOut-RBPre_ssSen_t1Tem_perat_ureTi_meOut
C05BB	TLE5012_VoltageFailure
C05C0	Pedal_Travel_Sensor_1_is_not_calibrated
C05C1	PTS2_CALIBRATION_MISSING
C05C2	FW_set_in_case_of_temperature_degradation_level1-MLIHi_ghTem_perat_ureLe_vel1
C05CC	Brake Master Cylinder Piston Position Sensor "A" Circuit Range/Performance
C05CF	Brake Master Cylinder Piston Position Sensor "B" Circuit Range/Performance
C05D6	PDU_EPS_01_-_Timeout_error-RBNet_ComSc_l_EPS_01_Timeo_ut
C05D8	4WD/AWD Clutch "A" Actuator Control Circuit/Open Circuit Current Above Threshold
C05D9	4WD/AWD Clutch "A" Actuator Control Circuit Performance Calibration / Parameter Memory Failure
C05DA	4WD/AWD Clutch "A" Actuator Control Circuit Low
C05DB	4WD/AWD Clutch "A" Actuator Control Circuit High
C05DC	DTC_CC_CLUTCH_PROTECTION
C05DD	4WD/AWD Clutch "A" Performance/Stuck Disengaged
C05DF	Implausible Allweeldrive Lamellar-Clutch Wear
C05E0	4WD/AWD Clutch "A" Position Sensor Circuit Circuit Voltage Out of Range
C05E1	EDD position sensor: Rationality Check- Clutch Disconnected State against clutch solenoid current
C05E4	4WD/AWD Clutch "A" Position Sensor Circuit Intermittent
C05E5	Initial Calibration Missing
C05E6	Detection of exceeding the maximum actuator angle
C05E7	4WD/AWD Clutch "B" Actuator Control Circuit/Open
C05E8	4WD/AWD Clutch "B" Actuator Control Circuit Performance Mechanical Failure
C05E9	4WD/AWD Clutch "B" Actuator Control Circuit Low
C05EA	4WD/AWD Clutch "B" Actuator Control Circuit High
C05EC	4WD/AWD Clutch "B" Performance/Stuck Disengaged
C05ED	4WD/AWD Clutch "B" Stuck Engaged
C05EF	4WD/AWD Clutch "B" Position Control Error
C05F0	Rear Drive Shaft Speed Sensor Circuit Low
C05F1	Rear Drive Shaft Speed Sensor Circuit High
C05F2	Rear Drive Shaft Speed Sensor Circuit Intermittent
C05F3	Rear Drive Shaft Speed Sensor Circuit
C05F4	Rear Drive Shaft Speed Sensor Circuit Range/Performance

C06

Kod	Açıklama
C0609	APB_Button_is_pushed_or_pulled_for_a_too_long_time-ApbBu_ttonA_lways_Pushe_dOrPu_lled
C060A	APB_Button_is_pushed_or_pulled_for_a_too_long_time-ApbBu_ttonA_lways_Pushe_dOrPu_lled
C060B	APB_left_motor_failure_in_H-bridge_during_CMSTinverse_(Enables_deactivated)-RBAPB_MOTLe_ftHBr_idgeC_MSTin_verse
C0610	APB_right_motor_failure_in_H-bridge_during_CMSTinverse_(Enables_deactivated)-RBAPB_MOTRi_ghtHB_ridge_CMSTi_nvers_e
C0615	APB_motor_electrical_coupling_failure_between_the_left_and_right_APB_motor_lines-RBAPB_MOTHB_ridge_CMCT
C0616	SPI_transfer_to_APB_ASIC_was_failed_(error_frame_wrong_address._timeout_CSIH_error)-Rbmic_ApbTr_ansfe_rErro_r
C0618	Inlet valve FL has short circuit to battery/terminal 30 (12V)
C0619	Offset_failure_of_Pedal_Travel_Sensor_1_(used_for_sPushrod)-Bsm_Pts1O_ffset
C061A	Offset_failure_of_Pedal_Travel_Sensor_2_(used_for_sPushrod)-Bsm_Pts2O_ffset
C061D	SECOBD:_Aktuator_Variable_Effort_Steering_Circuit_low
C061F	SECOBD:_Aktuator_Variable_Effort_Steering_Range/Performance
C0621	Safety_mechanism_of_the_Variable_Effort_Steering_Circuit_low
C0622	SECOBD:_Safety_mechanism_of_the_Variable_Effort_Steering_Circuit_high
C0623	SECOBD:_Safety_mechanism_of_the_Variable_Effort_Steering_Range/Performance
C0626	SECOBD:_Sensor_Variable_Effort_Steering_Circuit_low
C0627	SECOBD:_Sensor_Variable_Effort_Steering_Circuit_high
C0628	Auslassventil VL beim Cycle valve and Relay-test (CVRT) ausgefallen.
C0629	SECOBD:_Variable_Effort_Steering_Incorrect_Assembly
C062A	SECOBD:_Variable_Effort_Steering_ECU_Temperature_out_of_range_high
C062B	SECOBD:_Variable_Effort_Steering_ECU_Temperature_out_of_range_low
C062C	Combine_Event_-Phase_or_Offset_Current_2_out_of_range_high-RBBLM_OBDCu_rrent_2OORH_igh_OR_RBBLM_Curre_nt2Of_fsetH_igh
C062D	Cyclically_test_execution_of_ASIC-Valve-Driver_internal_Silent-Valve-Driver-Test_(SVDT)_in_hardware_is_not_stopped.-RBVLV_AsicC_hi
C0638	Outlet valve FL has short circuit to battery/terminal 30 (12V)
C0648	Einlassventil VR beim Cycle valve and Relay-test (CVRT) ausgefallen.
C0650	Inlet valve FR reports incorrect feedback
C0651	Inlet valve FR has short circuit to ground
C0658	Inlet valve FR has short circuit to battery/terminal 30 (12V)
C0668	Auslassventil VR beim Cycle valve and Relay-test (CVRT) ausgefallen.
C0670	Outlet valve FR reports incorrect feedback
C0671	Outlet valve FR has short circuit to ground
C0676	Brake_fluid_sensor_line_is_short_to_power_supply-RBBra_keFlu_idLev_elOut_OfRan_geHig_h
C0678	Outlet valve FR has short circuit to battery/terminal 30 (12V)
C0684	Differential Locking Actuator "A" Component or System Over Temperature
C0685	Einlassventil HL oder zweites Einlassventil desselben Bremskreises beim Drifttest ausgefallen.
C0686	Differential Locking Actuator "A" Position Sensor Circuit Voltage Above Threshold
C0687	Differential Locking Actuator "B" Position Sensor Circuit Voltage Above Threshold
C0688	Einlassventil HL beim Cycle valve and Relay-test (CVRT) ausgefallen.
C0689	4WD/AWD Clutch "A" Actuator Position Sensor "A" Circuit Voltage Above Threshold
C068A	4WD/AWD Clutch "A" Actuator Position Sensor "B" Circuit Voltage Above Threshold
C068F	4WD/AWD Clutch "A" Actuator Range Sensor Circuit Voltage Above Threshold
C0690	Damper Control Relay Circuit Malfunction
C0691	Damper Control Relay Circuit Range
C0692	4WD/AWD Disconnect Clutch Actuator Position Sensor "B" Performance or Incorrect Operation
C0693	Damper Control Relay Circuit High
C0695	Position Sensor Overcurrent (8 volt supply)
C0696	Position Sensor Overcurrent (5 volt supply)
C0698	Inlet valve RL has short circuit to battery/terminal 30 (12V)
C06A8	Auslassventil HL beim Cycle valve and Relay-test (CVRT) ausgefallen.
C06B0	Acceleration sensor (integrated): EEPROM content not correct or data cannot be read
C06B1	Combine_Event_-Cyclically_test_execution_of_ASIC-Valve-Driver_internal_Silent-Valve-Driver-Test_(SVDT)_in_hardware_is_not_stopped.
C06B2	Acceleration sensor (integrated): acceleration sensor is in reset (internal error)
C06B3	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt eine Messwertueberschreitung im Digitalfilter.
C06B4	Acceleration sensor (integrated): acceleration sensor is in initialization (internal error)
C06B5	Acceleration sensor (integrated): acceleration sensor detects internal error
C06B6	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt eine Bondverbindungsunterbrechung.
C06B7	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt eine Messbereichsueberschreitung A2.
C06B8	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt eine Messbereichsueberschreitung A1.
C06B9	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt einen Initialisierungs-Timeoutfehler oder einen Kommunikationsfe
C06BA	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt einen Taktzeitfehler.
C06BB	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt einen Empfindlichkeitsfehler A1.
C06BC	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt einen Empfindlichkeitsfehler A2.
C06BD	Acceleration sensor (integrated): acceleration sensor detects sensitivity error A2 (filtered signal)
C06BE	Acceleration sensor (integrated): acceleration sensor detects sensitivity error A1 (filtered signal)
C06BF	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt einen Temperatursensorfehler.
C06C0	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt eine Temperaturbereichsueberschreitung.
C06C1	Beschleunigungssensor (integriert): Beschleunigungssensor erkennt mehrfach sporadische Stoerungen.
C06D0	Yaw rate sensor (integrated): internal supply voltage (U5V) of the yaw rate sensor outside the valid range.
C06D1	Drehratensensor (integriert): Drehratensensorsignal ausserhalb dem gueltigen Bereich.
C06D2	Yaw rate sensor (integrated): yaw rate sensor detects internal error
C06D3	Drehratensensor (integriert): Drehratensensor erkennt einen Selbsttestfehler.
C06D4	Drehratensensor (integriert): Drehratensensor erkennt einen Temperatursensorfehler.
C06D5	Drehratensensor (integriert): Drehratensensor erkennt mehrfach sporadische Stoerungen.
C06D6	Drehratensensor (integriert): Drehratensensor erkennt eine Temperaturbereichsueberschreitung.
C06D8	Inlet valve RR has short circuit to battery/terminal 30 (12V)
C06E0	Electronic control module (ECU) faulty (yaw rate sensor and acceleration sensor: EEPROM content not correct or data cannot)
C06E1	Yaw rate sensor and acceleration sensor (integrated): temperature monitoring detected temperature deviation (temperature)
C06E2	Acceleration sensor (integrated): acceleration sensor is not calibrated or calibration status is invalid
C06E5	Network: signal selector lever position transmission (WHST) from transmission control module invalid
C06E8	Auslassventil HR beim Cycle valve and Relay-test (CVRT) ausgefallen.
C06F0	Outlet valve RR reports incorrect feedback
C06F1	Outlet valve RR has short circuit to ground
C06F8	Outlet valve RR has short circuit to battery/terminal 30 (12V)
C06FF	Brake Boost System Status Not Plausible Special Memory Failure

C07

Kod	Açıklama
C0711	MSG_SG_KLEMMEN_STATUS_01_TIMEOUT
C0712	PB_HBRIDGE_CURRENT_DEVIATION
C0713	CHASSINF_HW_SW_INCOMPATIBLE
C0714	EEP_E_COMPARE_FAILED
C0715	MSG_MS2S_VEHICLE_AMBIENT_TEMPERATURE_INVALID
C072C	CAN system: CAN message ID 408h instrument cluster too short
C072D	CAN system: CAN message ID 408h instrument cluster failed
C0730	CAN system: CAN message ID 428h transfer case control module (AWD) too short
C0731	CAN system: CAN message ID 448h transfer case control module (AWD) too short
C0732	CAN system: CAN message ID 428h transfer case control module (AWD) failed
C0733	CAN system: CAN message ID 448h transfer case control module (AWD) failed
C0735	CAN system: CAN message ID 236h steering angle sensor (LRW-NCV3) too short
C0736	CAN system: CAN message ID 236h steering angle sensor (LRW-NCV3) failed
C0737	CAN system: CAN message ID 3B8h parameterizable control module (retarder) too short
C0738	CAN system: CAN message ID 3B8h parameterizable control module (retarder) failed
C0739	CAN system: CAN message ID 330h brake control module (ESP) failed
C073A	CAN system: CAN message ID 234h steering angle sensor (LWS-NCV2) failed. Analog 0x4736 but different set condition
C0740	CAN Sys: faulty initialisation of the CAN controller.
C0742	CAN system: monitoring has detected a wiring or signal level fault.
C0743	CAN system: high or low lines faulty.
C0747	CAN system: faulty initialization of message in CAN controller
C074C	CAN system: CAN message ID 608h engine control module too short
C074D	CAN system: CAN message ID 608h engine control module failed
C074E	CAN system: CAN message ID 238h jacket pipe module too short
C074F	CAN system: CAN message ID 238h jacket pipe module failed
C0750	CAN system: CAN message ID 418h transmission control module too short
C0751	CAN system: CAN message ID 418h transmission control module failed
C0752	CAN system: CAN message ID 312h engine control module too short
C0753	CAN system: CAN message ID 312h engine control module failed
C0754	CAN system: CAN message ID 308h engine control module too short
C0755	CAN system: CAN message ID 308h engine control module failed
C0756	CAN system: CAN message ID 212h engine control module too short
C0757	CAN system: CAN message ID 212h engine control module failed
C0758	CAN system: CAN message ID 210h engine control module too short
C0759	CAN system: CAN message ID 210h engine control module failed
C075A	CAN system: CAN message ID 240h electronic ignition switch too short
C075B	CAN system: CAN message ID 6F4h electronic ignition switch too short
C075C	CAN system: CAN message ID 240h electronic ignition switch failed
C075D	CAN system: CAN message ID 6F4h electronic ignition switch failed
C0760	CAN system: internal processing error in evaluation of vehicle identification number (VIN)
C0761	CAN system: vehicle identification number (VIN) or odometer value not received
C0762	CAN system: CAN message ID 6FAh electronic ignition switch too short
C0763	The status 'front axle engaged' is invalid.
C0764	t.b.d.
C0770	CAN system: CAN message ID 2F3h engine control module too short
C0771	CAN system: CAN message ID 2F3h engine control module failed
C07C0	CAN system: error in CAN DPRAM in control module
C07C2	CAN system: CAN message ID 258h adaptive cruise control failed
C07D3	CAN: odometer signal invalid
C07F0	System status in EEPROM has invalid value
C07F1	System status outside the permissible range.

C08

Kod	Açıklama
C0800	Brake_Fluid_sensor_detected_the_state_of_fluid_empty-RBBra_keFlu_idEmp_ty
C0802	Variant code: invalid configuration of vehicle dynamics control trailer sway logic (FZRTol) stored or EEPROM is defective.
C0803	This_failure_word_will_be_logged_when_brake_stress_of_any_one_wheels_reaches_the_fading_warning_level1_threshold.-BCS_Stres_sInde_
C0804	Variant code: transmitted variant value outside the permissible range.
C0805	Reduced_pressure_build_up_in_plunger._Sucked_air_inside_the_plunger_during_TTI_or_RPL_or_active_test_during_start_up.-AIM_RADAi_rP
C0806	Combine_Event_-WSS_undervoltage_has_been_detected_for_XY_wheel-RBWss_XYUnd_erVol_tage
C0845	Variant code: stored variant could not be verified with CAN variant
C0861	RoadRail: read access to RoadRail EEPROM cell failed
C0896	Device Voltage Range/Performance

C09

Kod	Açıklama
C0900	Brake function monitoring: the preventive maintenance function is deactivated.
C0901	Brake function monitoring: brake function monitoring FL detected error from set threshold values
C0902	Brake function monitoring: brake function monitoring FR detected error from set threshold values
C0903	Brake function monitoring: brake function monitoring RL detected error from set threshold values
C0904	Brake function monitoring: brake function monitoring RR detected error from set threshold values
C0905	Brake function monitoring: brake function monitoring FL detected error from set threshold values or
C0906	Brake function monitoring: brake function monitoring FR detected error from set threshold values or
C0907	Brake function monitoring: brake function monitoring RL detected error from set threshold values or
C0908	Brake function monitoring: brake function monitoring RR detected error from set threshold values or
C0909	Brake function monitoring: brake function monitoring FL detected brake pad overheating
C090A	Brake function monitoring: brake function monitoring FR detected brake pad overheating
C090B	Brake function monitoring: The monitoring of brake function HL detected brake pad overheating.
C090C	Brake function monitoring: The monitoring of brake function HR detected brake pad overheating.
C0930	Switching valve USV1 has short circuit to battery/terminal 30 (12V).
C0950	Wheel speed sensor: 2 wheel speed sensor faults occurred at the same time (store).
C0951	Wheel speed sensor: 2 wheel speed sensor faults occurred at the same time.
C0955	Umschaltventil USV2 oder USV1 beim Drifttest ausgefallen.
C0958	Umschaltventil USV2 beim Cycle valve and Relay-test (CVRT) ausgefallen.
C0970	Hydraulikueberwachung: Ueberlast QS-Mode.
C0998	Hochdruckschaltventil HSV1 beim Cycle valve and Relay-test (CVRT) ausgefallen.
C09A1	Longitudinal control: Memory protection unit detects unauthorized memory access from longitudinal control to protected memory area.
C09C0	Network: Message EM2_RS4 (Engine control module) not correct.
C09C1	Network: Message EM2_RS4 (Engine control module) failed.
C09C2	Network: Signal Electric motor brake torque (Actual value) invalid.
C09C3	Network: Signal Electric motor speed (Actual value) invalid.
C09C8	Network: Signal Brake torque request radar decision unit (BrkTrq_Rq_RDU) from Radar decision unit control module invalid.
C09C9	Network: Signal Engine torque request radar decision unit (EngTrq_Rq_RDU) from Radar decision unit control module invalid.
C09CA	Network: Signal Braking attention assistance system (AS_Brk) from External torque interface control module or from Standstill
C09CB	Network: Message (CMS_PI_STAT) from Radar decision unit control module not correct (Data corruption error).
C09CC	Network: Message (CMS_PI_STAT) from Radar decision unit control module not received (Timeout error).
C09D0	Network: Message (MRM_A1) from Cladding tube module not correct (Data corruption error).
C09D1	Network: Message (MRM_A1) from Cladding tube module not received (Timeout error).
C09E0	High pressure control valve HSV2 reports incorrect feedback.
C09E1	Network: Message MS_268h (Engine control module) failed.
C09E2	Network: Signal Accelerator pedal value (Driver) invalid.
C09F0	Network: Message MS_2F3h (Engine control module) not correct.
C09F1	Network: Message MS_2F3h (Engine control module) failed.
C09F4	Network: Signal Engine status (Actual value) invalid.

C0A

Kod	Açıklama
C0A3F	Lateral acceleration sensor detects open circuit fault.
C0A40	Lateral acceleration sensor detects gradient monitoring implausible fault.
C0A41	Lateral acceleration sensor detects implausible gradient fault.
C0A42	Lateral acceleration sensor detects sensor signal outside allowable range fault.
C0A44	Querbeschleunigungssensor erkennt auf Vergleichsfehler.
C0A45	Lateral acceleration sensor detects a model-based comparison fault.
C0A46	Querbeschleunigungssensor erkennt auf Stillstand-Offsetfehler.
C0A47	Querbeschleunigungssensor erkennt auf Langzeitabgleich-Offsetfehler (LZA).
C0A49	Querbeschleunigungssensor erkennt auf Signalbereichsfehler.

C0B

Kod	Açıklama
C0B22	Drehratensensor erkennt auf Langzeitabgleich-Offsetfehler.
C0B26	Drehratensensor erkennt auf Empfindlichkeit-Abgleichsfehler.
C0B28	Drehratensensor erkennt auf Schnellabgleich-Offsetfehler.
C0B30	Drehratensensor erkennt auf Signalgradientfehler.
C0B34	Drehratensensor erkennt auf Stillstand-Offsetfehler.
C0B38	Drehratensensor erkennt auf Signalbereichsfehler.
C0B3A	Yaw rate sensor shows faulty signal states in the model-based comparison with the steering angle sensor.
C0B3F	Drehratensensor erkennt auf Installationsfehler (Sila).
C0BB5	Drehratensensor erkennt auf internen Sensorfehler (Selbsttestfehler).
C0BB7	Rotational rate sensor: Message checksum CRC not correct.
C0BB9	Rotational rate sensor type not allowed.
C0BBA	Rotational rate sensor not available because rotational rate status signal PSIP2 faulty.
C0BBB	Rotational rate sensor not available because lateral acceleration status signal AY2 faulty.
C0BBC	Rotational rate sensor not available because longitudinal acceleration status signal AX1 faulty.
C0BBD	Rotational rate sensor not available because lateral acceleration status signal AY1 faulty.
C0BBE	Rotational rate sensor not available because rotational rate status signal PSIP1 faulty.
C0BBF	Rotational rate sensor: Message checksum ID1 not correct.
C0BC0	Rotational rate sensor: Message checksum ID2 not correct.
C0BC2	Rotational rate sensor: Message checksum ID7 not correct.
C0BC6	Rotational rate sensor: Message counter ID7 not correct.
C0BD9	Longitudinal acceleration sensor detects a signal range fault.
C0BDA	Longitudinal acceleration sensor detects a long-term adjustment offset fault (LTC).
C0BDB	Longitudinal acceleration sensor detects a comparison fault.
C0BDC	Longitudinal acceleration sensor detects an offset value outside the permissible range.
C0BDD	Longitudinal acceleration sensor detects invalid offset values.
C0BDE	Control module detects faulty longitudinal acceleration sensor.
C0BDF	Control module access error during longitudinal acceleration sensor detection.
C0BE0	CAN System: CAN message ID1h Rotational rate sensor TX too short.
C0BE1	CAN System: CAN message ID2h Rotational rate sensor TX too short.
C0BE3	CAN System: CAN message ID7h Rotational rate sensor TX failed.

C0D

Kod	Açıklama
C0D2E	Steering angle sensor shows faulty signal states in the model-based comparison with the yaw rate sensor.
C0D30	Steering angle sensor detects a long-term adjustment offset fault (LZA).
C0D31	CAN: Steering angle sensor message checksum not correct.
C0D34	Steering angle sensor detects a signal gradient fault.
C0D35	CAN: steering angle sensor detects an internal sensor fault (self-test fault).
C0D36	Steering angle sensor detects a signal range fault.
C0D37	CAN: Steering angle sensor message count not correct.
C0D38	Steering angle sensor detects a signal monitoring fault.
C0D3C	Steering angle sensor detects an installation fault (Sila).
C0D81	Fahrzeug-Notbremse.
C0D82	Fahrzeugdynamikregelung kontinuierlich.
C0DC0	Long-term calibration error (Monitoring and offset compensation).

C0E

Kod	Açıklama
C0E40	Application software switches system into Emergency-EBD mode.
C0E51	Fahrtest: Fahrtest aktiviert.
C0E5C	End of Line (EOL): Lateral acceleration sensor sensitivity exceeds limit value (road test).
C0E60	Application Software (ASW) detects monitoring error (Messages) in startup phase.
C0E61	Driving test: the longitudinal acceleration sensor is being tested (status display).

C0F

Kod	Açıklama
C0F81	Value added function server (VAFS) detects non-corresponding controller version.
C0F82	Value added function server (VAFS) detects a data transmission checksum fault.
C0F83	Value added function server (VAFS) detects a data transmission timeout fault.
C0F84	Value added function server (VAFS) detects Serial Processing Interface (SPI) connection and transmission error.
C0F89	Value added function server (VAFS) detects an analog/digital converter (ADC) transmission checksum fault.
C0F8A	Value added function server (VAFS) detects a platform software (PSW) or application software (ASW) transmission fault.
C0F8B	Value added function server (VAFS) erkennt auf Hardwarenahe Software (HSW)-Allgemeinfehler.
C0FE1	Electronic control module (ECU) defect (Proportional valve (ECO valve): Software version not supported or EEPROM defect
C0FF0	Proportional valve (ECO valve): Supply voltage line (ECO_P) has short circuit to positive.

Diğer bloklar

• B3Önceki blok
• Tüm bloklarAudi · Porsche · Bentley · Lamborghini
• C1Sonraki blok

Bu kodları kullanan markalar

• Audi81 model
• Porsche7 model
• Bentley1 model
• Lamborghini1 model

Kod metinleri kaynak dilinde gösterilir; çevirisi olmayan kayıt ham kalır. Kaynak: CarCoding arıza kodu veritabanı.